Contact Us

A factory is a point. A mine is a surface. A pipeline is a line — hundreds or thousands of kilometres long, with monitoring sites scattered along the route and often no mains power, control room or reliable wired connection nearby.

The instruments have been there for decades. The challenge is getting their readings back to the people who need them.

This field guide examines how industrial cellular routers connect pipeline infrastructure outside hazardous areas, including cathodic protection stations, valve sites, metering skids and remote terminal unit (RTU) networks. It focuses on the practical requirements that determine whether a remote site remains connected: serial communication, digital I/O, independent alarms, solar power, environmental protection and fleet management.

Written by E-Lins Engineering Team

A small steel equipment cabinet and a short antenna beside a length of above-ground pipeline running across a remote open right-of-way at dawn, with the corridor receding into the distance.

The Shape of the Problem

An oil and gas pipeline is a network of isolated sites spread across hundreds or thousands of kilometres. Valve stations, cathodic protection (CP) rectifiers, metering skids and remote terminal units may operate in fields, deserts, wetlands or remote rights-of-way, far from technicians and permanent power infrastructure.

Most sites already have instruments that measure pressure, flow, valve position or rectifier status. The challenge is transporting that data reliably to a control room without the cost of extending fibre to every remote location.

A pipeline is therefore not simply a place that needs network coverage. It is a long line of individual sites, each requiring a suitable connection, power source and maintenance strategy.

The cost of connecting those sites is measured not only in router hardware, but also in installation time, power infrastructure, communications charges and future service visits.

The consequences of losing connectivity can vary considerably. A valve-status update may be delayed. A metering site may stop reporting operational data. A cathodic protection system may lose power without the control room receiving an immediate notification.

Industrial cellular routers provide a practical last-mile connection where cellular coverage is available. They do not replace the operator’s SCADA backbone or specialist monitoring systems. Their role is to carry data from remote field equipment to the systems that collect, analyse and act on it.

The reframe for this article: a pipeline is not a place that needs network coverage. It is a thousand-kilometre line of isolated sites that each need their own link out, and the cost of giving them one is measured in dollars per kilometre of wilderness, not in features per router. The constraint is not “which router” — it is “how do you connect a thing that is three hundred kilometres from the nearest technician and has no power?”
Three plan-view panels comparing a factory drawn as a single point, a mine drawn as a surface, and a pipeline drawn as a long line with nine small sites spaced along it.Industrial Cellular Routers

What Actually Sits Along a Pipeline

Pipeline connectivity requirements depend on the type of site being connected. Although the equipment shares the same outdoor environment, different locations place different demands on the communications system.

Site typeTypical equipmentMain connectivity requirement
Valve and RTU stationsValves, actuators, pressure instruments and RTUsSerial communications, valve-state monitoring and reliable remote access
Cathodic protection stationsRectifiers, current shunts and reference-cell monitoring equipmentFault reporting, power-state monitoring and independent alarms
Metering skidsFlow, pressure and temperature instruments, sometimes chromatographsReliable data transport and sufficient network capacity
Pig launchers and receiversInspection-pig launch and receiving equipmentRemote status monitoring and operational visibility during pig runs
Wellheads and pump stationsProduction, pumping and monitoring equipmentCommunications for local equipment and potential aggregation of remote-site traffic

These sites may already use a licensed radio network, satellite communications, an existing private network or no remote connection at all. Cellular connectivity offers another option when coverage, service availability and the application’s requirements make it suitable.

The main advantage is that cellular infrastructure may already be available near parts of the pipeline route. Instead of constructing a dedicated wired connection to every site, an operator can use a cellular link to transport relatively small amounts of operational data.

However, coverage must be verified at the actual installation location. A cellular tower that appears close on a map does not guarantee a reliable signal at a valve station, inside a metal cabinet or behind difficult terrain.

Cellular connectivity is best treated as a site-specific engineering decision rather than a universal replacement for radio, satellite or fibre.

A straight pipeline with five differently drawn station icons along it — valve, cathodic rectifier, metering skid, pig launcher and wellhead — each with a dashed line rising to a single cellular uplink cloud.
“Our problem was never the instrumentation. The valve station knew it was open. The CP rectifier knew it had lost power. The meter knew what it had measured. The problem was that none of them could tell us, because there was no wire to tell us on. Cellular is the wire we never had to bury.”
Pipeline integrity engineer, midstream operator

The RTU That Has Been There Since 1994

The first thing to understand about pipeline connectivity is that you are almost never starting from nothing. The valve station already has an RTU, and that RTU speaks serial. The job of the router is not to replace the RTU — it is to give the RTU a way out of the field.

The range supports exactly the interfaces a legacy pipeline site presents. Serial Port RS232 or RS485 covers both the older RS-232 links and the RS-485 multidrop segments that daisy-chain instruments along a station. Modbus and DTU (serial to cellular) is the mechanism that turns those serial bytes into packets and carries them over the cellular link to the SCADA master — Modbus on the serial side, a tunnel or a polling session on the cellular side. For sites that already run Modbus, this is the difference between “we install a whole new telemetry system” and “we plug a router into the port that was already there.”

How this differs from the substation story. A companion E-Lins article covers DNP3 and Modbus serial-to-cellular for substations in detail — the protocol mechanics, the master/slave polling, the tunnel design. This article is deliberately not that. It assumes you have read how a serial-to-cellular bridge works and asks the harder pipeline question instead: when you have hundreds of those bridges scattered across a thousand kilometres, how do you keep them alive, powered, provisioned and auditable? The protocol is the easy part. The fleet is the work.

There is a second, quieter interface that matters more on a pipeline than on a factory floor: the discrete contact. DI/DO (Digital Input & Output) port * 4 gives four digital lines per unit, and on a valve station those four lines carry more operational truth than the serial port. Valve open / closed / fault, local / remote selector, an ESD contact, a cabinet-door or tamper switch — these are the states a control room actually acts on, and they do not need a protocol stack. They need a dry contact read remotely, with the state available both over the data tunnel and, as the H700 and H750 specify, by SMS.

A three-lane signal-path diagram showing a legacy RTU's serial and digital interfaces bridging into an industrial router with a cellular uplink to the SCADA master and a separate fleet-management loop.
What a valve-station router actually talks to
The RTU, over RS-232 or RS-485. Legacy or current, the serial port is the front door.
Modbus instruments and the SCADA master. Modbus and DTU (serial to cellular) carries the polling session to where the master lives.
Discrete states, over DI/DO. Valve position, fault, local/remote, tamper — four lines, read remotely and by SMS.
The field cabinet itself. A door switch, a supply-state contact, a temperature or flood sensor — the things that explain why the site is quiet before anyone drives out.

Cathodic Protection: The Silent Failure

If you ask a pipeline integrity engineer which site keeps them awake at night, a surprising number say the cathodic protection rectifier — and not the obvious candidate, the valve. The reason is the failure mode. A valve that fails closed is noticed; a line goes down and someone picks up the phone. A CP rectifier that loses its AC supply keeps the valve working and the line flowing, and simply stops protecting the pipe. The pipe does not complain. It corrodes, slowly, for months, until the next close-interval survey or an in-line inspection finds metal loss — or worse, finds nothing because the failure was at a holiday in the coating no one was watching.

This is the textbook silent failure, and it is where an industrial router earns its place more clearly than almost anywhere else on the line. The requirement is not bandwidth. A rectifier status, an output current, a reference-cell voltage and a supply-state contact are a handful of bytes. The requirement is that those bytes leave the rectifier site even when the rectifier site has a problem — including when its own link is the thing that has failed.

Design the alarm path separately from the data path. The range supports SMS/Voice Control and Alarm and SMS control, SMS gateway and SMS alarm — SMS or a call to bring a router online or offline, to reboot it, and to read signal and status. That matters at a CP site because an SMS alarm can leave over the signalling channel even when the data tunnel is down. A “rectifier has lost AC” warning that only works while the data connection works is not a warning; it is a record of a time when conditions were good.

What a CP site needs to report maps onto what the range offers at the cabinet: DI/DO (Digital Input & Output) port * 4 for the rectifier fault contact and the AC-loss contact; Serial Port RS232 or RS485 for a rectifier with a serial interface or a reference-cell logger; and Modbus and DTU (serial to cellular) to carry the readings to the integrity system. The digital inputs on the H700 and H750 are specified as 4 ports, 0-3.3V. Support status monitor via SMS and Email — logic-level sensing, readable both remotely and by SMS. A CP site that reports “I have lost AC” or “my output current has dropped to zero” explains most of its own failures before a pig run ever finds them.

A three-lane signal-path diagram for a cathodic rectifier showing AC-loss and current readings feeding a router, a data tunnel and a dashed SMS alarm path leaving it, and the SMS path continuing unbroken when the data tunnel is cut.
“The rectifier that matters is the one that went quiet, not the one that tripped. If ‘I have lost my anode current’ leaves the site on its own, the corrosion problem is a log entry. If it doesn’t, it is a coating holiday somebody finds with a smart pig, three seasons late.”
Corrosion and cathodic-protection specialist

Leak Detection and the Third Party

Two leak threats dominate a pipeline’s risk register, and they are opposite in nature. The first is the rupture — a sudden, large, obvious event that every leak-detection system and every operator will see. The second is the slow, small release that no mass-balance or negative-pressure-wave system is tuned to catch, and the third-party strike that never reaches the instrumentation at all because it happens to the pipe, not the equipment.

For the instrumentation-side leak detection — flow balance, pressure transient, negative-pressure-wave correlation — the router’s role is transport, and one specific property matters: time. These algorithms need samples from stations tens or hundreds of kilometres apart to be time-aligned to within a fraction of a second. That is a clock-synchronisation problem, not a router problem, but it is a router problem in the sense that the router is what carries the time-stamped samples, and a link that drops for ten seconds every hour will quietly wreck a transient-detection threshold. The range’s standard NTP/SNTP client and stable cellular session are what keep the samples on the same clock; we are not claiming a survey-grade time source here.

Be precise about what the router does for leak detection. It carries the instrument data and keeps the sites on a common clock. It is not a leak-detection system, and it is not a replacement for the fibre-optic distributed acoustic sensing (DAS) or the right-of-way camera network that a high-consequence line will also run. Those are separate systems with their own hardware; the router simply provides a link some of their nodes use. Keep the jobs distinct and the specification stays honest.

The third-party threat — excavation through the line — is the one where the router’s contribution is least glamorous and most useful. You cannot stop a backhoe with a cellular signal, but you can make the right-of-way observed. A cabinet at an isolated site, with the option of POE PD or PSE. 802.3af and 802.3at to power a camera or an access point on the same drop, plus external antenna connectors for high gain antennas replacement to reach a distant cell, turns a blind spot into a monitored segment. On a line that crosses a thousand kilometres of development, the sites that can see their own right-of-way are the sites that turn “someone dug through us” into “we have the timestamp and the picture.”

Power in the Wilderness

On a pipeline, power is rarely a clean 230 V socket in an air-conditioned room. It is a solar array and a battery in a cabinet, feeding your router through a charge controller and a long cable, in a place where a lightning strike is an ordinary seasonal event and the nearest grid connection is kilometres away. The most common cause of an unreliable pipeline network is not radio coverage — it is an input power design that assumed a building and met a right-of-way.

The range is specified with a wide DC input precisely for this reason: 5-40V DC voltage input range (5-60V DC option), with Dual Power Inputs/Power Failover. A 12 V battery bank, a 24 V site bus and a 48 V PoE arrangement all sit inside the range, and dual inputs mean the unit can survive the loss of one supply — which on a solar site means it can ride through the failure of the primary feed and keep reporting on the secondary.

Power facts that decide a remote-site design
—Wide DC input. 5-40V DC (5-60V DC option) — covers 12 V, 24 V and 48 V site buses without a separate converter.
—Dual inputs with failover. Dual Power Inputs/Power Failover — ride through the loss of one feed.
—Fusing, by input voltage. The datasheets specify For 9–24 VDC installations, use a 3 A fuse and For > 24 VDC installations, use a 2.5 A fuse — size the inline fuse to the supply you actually use.
—Transient and reverse-polarity protection. Reverse polarity and transient voltage protection per ISO 7637-2 — a wiring mistake or a mill motor switching no longer means a second truck trip. Some platforms add anti-lightning protection.

Those protections describe exactly the failure a pipeline electrician will actually cause. Reverse polarity happens when a site cable is re-terminated in a hurry at a valve station. Transient voltage happens when lightning couples into a long antenna feed or a welder works nearby. A router that survives both is a router that does not turn a field mistake into a site outage.

Size the energy budget against the reporting interval, not the peak. Idle draw is a fraction of transmit draw — on these platforms the typical figure is Idle: typical=100mA@12VDC. A solar- or battery-fed site’s energy budget is therefore dominated by how often the router transmits and how long it holds the radio up, not by its headline power rating. On a pipeline, where most of the line is off-grid, that is a design decision made once and lived with for the life of the site.

One more pipeline-specific note: a valve station or CP rectifier often sits on a supply that is itself monitored, and it is worth having the cabinet report its own power state as a discrete input. A site that reports “I am on battery” or “I have lost mains” explains most of its own outages before anyone drives out — and on a pipeline that drive is measured in hours, not minutes.

An off-grid energy-budget diagram showing a solar array charging a 12-volt battery feeding a router with an idle current of 100 milliamps and short transmit bursts, with a bar chart arguing the reporting interval sets the budget.

The Enclosure Is the Engineering

A valve station has no air conditioning. A CP rectifier has no plant room. These sites live in the open, and the enclosure you put the router in is more of an engineering decision than the router model you choose. The cabinet decides whether the hardware survives its first wet season, and on a pipeline the cabinet is doing most of the work.

The ingress ratings in the range describe two different things. The cased units — the bulk of the range — are specified as Robust Metal Case is ruggedized for vibration, shock, provide IP30 protection. IP30 is a metal case that keeps out fingers and most debris; it is not a weatherproof rating, and it is meant to live inside a properly sealed cabinet. The exception is the H820QO, specified as IP68 outdoor water proof and dust proof and IP68 grade anti-dust and anti-water enclosure for outdoor installation — a genuinely outdoor enclosure for an exposed site.

The four things to confirm before you commit a cabinet to a right-of-way: (1) the actual enclosure you will use and its thermal behaviour in sun and shade; (2) whether any part of the site falls inside a classified (hazardous) area — see section 03; (3) the ingress rating you actually need, remembering that on the cased units it is the cabinet that must be weatherproof, while the H820QO brings its own IP68 enclosure; (4) the lightning exposure of the antenna and cable run, and whether a surge arrester belongs on the antenna feed. None of these is a router specification; all of them decide whether the router survives year one.

The temperature figure deserves a second look, because it is often read the wrong way. −35 °C to 75 °C is the ambient air operating range; storage is −40 °C to 85 °C. A cabinet in full sun on a desert right-of-way is not at ambient — it is at ambient plus the greenhouse effect of its own enclosure, which can easily add twenty degrees or more. A router rated to 75 °C in a black steel box in the sun is being asked to operate at the top of its range, and the honest engineering answer is a shade structure, a vented cabinet or a light-coloured enclosure. The rating is the ceiling, not the design condition.

On a pipeline, this is not theoretical. Right-of-ways run through flood plains, through freeze-thaw cycles that crack seals, and through dust that is fine and abrasive. The practical guidance is unglamorous: put the IP30 cased units inside a sealed, shaded, vented cabinet rather than in the open, seal the cable entries, aim the antenna so water cannot track into it, and put “inspect and clean” on the site’s maintenance schedule. In the field, a well-sealed cabinet will outlast an exposed unit with a higher headline rating. The rating tells you what the box does; the installation decides what the site gets.

Two side-by-side drawings comparing a cased IP30 router inside a sealed cabinet with a sun heat-rise arrow above it, against a single self-contained IP68 outdoor enclosure with an integral antenna.

A Thousand Kilometres of Fleet

A pipeline network is not one router. It is a few hundred valve stations, CP rectifiers and metering skids spread across a thousand kilometres, and the number grows as the line is extended. The economics change completely once the count passes the point where each site can be treated as a small project. The cost of one truck trip, multiplied by the trips a site needs over its life, will exceed the hardware inside it within a few years. That makes remote management a pipeline requirement, not an IT preference.

The range is cloud-managed through the E-Lins NMS, with TR-069, SNMP, web management and SMS among the management paths, and firmware updatable locally, remotely (LAN, Wi-Fi and OTA WAN) and NMS. On an isolated site, OTA firmware updates matter more than in a plant: a site three hundred kilometres from a technician should not need a visit just to reach the current software baseline.

The fleet habits that matter on a pipeline
—Provision by template, not by hand. A site’s configuration — tunnel, polling, input rules, alert paths — should be a template with a few per-site variables, so a new or rebuilt site is a data entry rather than a build. Individually configured sites cannot be audited, because there is no baseline.
—Monitor health, do not discover failure. Track the link, the signal, the supply state and the last-seen time for every site, so the dashboard tells you about the degraded station before a control room does.
—Keep the SIM strategy deliberate. The range supports Multi-carrier 2G/3G/4G LTE support with Dual SIM card slot and a documented dual-SIM working mode list — 1 Only SIM1 or SIM2, 2 time, 3 signal strength, 4 dial fail, 5 data limit, 6 ICMP check, 7 Load Balance, 8 Bonding (pending) — with Advanced Modem Failure Check and Dual SIM instant failover switching. On a remote site a second SIM is the cheapest redundancy on the bill of materials.
—Let SMS be an independent back door. SMS control, SMS gateway and SMS alarm let a site be rebooted, queried or alerted over a channel that does not depend on the data tunnel. That is the difference between managing a site and waiting for it.

There is a pipeline-specific discipline buried in the fleet question, and it is worth stating plainly: name and number sites by chainage, not by place name. A valve station called “the one past the Miller farm” is misnamed within a year, when the farm is sold and the access road is rerouted. Call it “CP-147+200” or “VS-312+500” — its distance along the line — and keep its physical position as data. A network whose identity survives the move is a network you can still audit after the right-of-way changes. On a line that is extended and rerouted for decades, that discipline is what keeps the asset register from silently lying to you.

A strip map of a pipeline with twelve small sites labelled by chainage codes, three older sites struck through as removed and three new sites added beyond them, all uplinked to a single network-management cloud.

What to Spec

The router question on a pipeline is rarely “which model” in isolation — it is “which model for which site, and what options do I have to tick on the order code so it actually works when it gets to the right-of-way.” The table below maps the common site types to the capabilities that matter, all drawn from the E-Lins datasheets. None of these platforms is explosion-proof; every deployment in the table is on the non-hazardous side of the line.

Site typeWhat it must doCapabilities to confirmSuited platforms
Valve / RTU stationCarry serial RTU to SCADA; read valve stateRS232/RS485, Modbus/DTU, DI/DO×4, dual SIMH750, H700, H685
CP rectifierReport AC loss & output current; alarm when link is downDI/DO×4, SMS alarm, RS232/RS485H750, H700
Metering / monitoring skidHigher data volume; power a camera or APGigabit Ethernet, PoE PSE 802.3af/at/btH900
Exposed / no cabinetSurvive weather with no shelterIP68 outdoor enclosureH820QO
Solar, space-limitedLow idle draw; small footprint5-40V input, Idle ~100mA@12VDC, compactM300, M400
Position-aware nodeReport its own location on a moving/extended lineGPS/GNSS (Option)M300, H685m
The five confirmations to make before ordering
—GNSS option. If you want the node to report its own position, confirm GPS/GNSS (Option) GPS, GNSS, Beidou is on the order code — it is an option, not a default, and it is position for the node, not a survey instrument.
—Serial electrical standard. Confirm RS-232 or RS-485 to match the RTU you are plugging into; they are not interchangeable at the connector.
—PoE direction. If you need to power a camera, confirm POE PSE. If you want the router fed by PoE, confirm POE PD. “PoE” alone does not tell you which way the power flows.
—Temperature and ingress rating. Confirm −35…+75 °C ambient is adequate for the actual (in-cabinet, in-sun) condition, and whether you need the IP68 H820QO or a cased unit inside your own cabinet.
—DI/DO voltage level. Confirm the digital input level (the H700/H750 specify 0-3.3V logic inputs) matches the contacts you intend to read, and that the hazardous-area boundary keeps the site on the non-classified side.

Three Pipeline Patterns

The detail above collapses into three recurring patterns. If you can specify these three, you can specify a pipeline network.

Pattern A — The CP Rectifier Network
A few hundred solar-powered rectifier sites, each reporting AC-loss, output current and a fault contact, with an SMS alarm that leaves when the data tunnel does not. The hero capability is DI/DO×4 plus SMS control, SMS gateway and SMS alarm; the design discipline is the power budget against the reporting interval. This is the pattern that turns silent corrosion into a log entry.
Pattern B — The Valve-Station RTU
A serial RTU that has been there since the nineties, now with a cellular bridge. RS232/RS485 and Modbus and DTU (serial to cellular) carry the polling session to the master; DI/DO×4 carries valve state and local/remote. Dual SIM with documented failover modes is what keeps a site three hundred kilometres from a technician from becoming a site visit.
Pattern C — The Metering / Monitoring Skid
The higher-volume, better-connected end of the line: custody metering, a chromatograph feed, and a camera watching the right-of-way. Gigabit Ethernet plus POE PSE 802.3af/at/bt to power the camera on the same drop; a stable cellular session for the data. This is where the H900/H900f platforms earn their place.
A compact metering or valve skid on a concrete pad in a remote open setting at late afternoon, with an equipment cabinet, a short antenna mast and a solar panel beside a run of above-ground pipeline.

The common thread is not a product. It is that on all three patterns the decisions that decide success are the alarm path, the power budget, the enclosure and the option set — and the router is the component that makes those decisions physically possible, rather than the one that makes them for you.

Frequently Asked Questions

Q1:Are E-Lins routers explosion-proof or certified for hazardous areas?

No. E-Lins industrial routers are not explosion-proof and carry no hazardous-area certification (no ATEX, IECEx or equivalent). They are general-purpose industrial routers for ordinary and outdoor industrial environments and must not be installed inside a classified hazardous area, near a potential gas release, or anywhere a flammable atmosphere can form. Those locations require equipment certified for the specific zone, gas group and temperature class, installed under the operator’s hazardous-area procedures. On a pipeline, apply these routers only outside the classification boundary — the RTU shelter’s non-hazardous side, the CP rectifier enclosure, the fibre/telecom hut, the solar cabinet.

Q2:Can the GNSS option be used for pipeline positioning or leak location?

No. The GNSS option provides position for the network node — so a relocatable or extended-line site can report where it is. It is not a survey instrument and not an inertial or mapping system, and no accuracy figure in the datasheet should be read as pipeline-location or leak-locating performance. Where the operator needs centimetre positioning or leak geolocation, that is dedicated survey or DAS equipment whose data happens to travel over a link these routers can carry.

Q3:Does this replace the SCADA backbone or the leak-detection system?

No. The router is the last mile — the link that carries instrument data from an isolated site to wherever the master or the leak-detection server lives. It is not a SCADA master, not a DNP3/Modbus controller in its own right beyond serial bridging, and not a leak-detection algorithm. Keep those systems as they are; the router simply gives them a wire they never had to bury.

Q4:How does the link stay up at a remote site with one cell tower?

The range supports Dual SIM instant failover switching across carriers, with a documented working-mode list — 1 Only SIM1/SIM2, 2 time, 3 signal strength, 4 dial fail, 5 data limit, 6 ICMP check, 7 Load Balance, 8 Bonding (pending) — plus Advanced Modem Failure Check. A second SIM on a different carrier is the cheapest redundancy on the bill of materials, and external antenna connectors for high gain antennas replacement let you aim a high-gain antenna at the serving cell.

Q5:How do I power a site that has no mains supply?

A solar array and battery, feeding the router through its wide DC input: 5-40V DC (5-60V DC option) with Dual Power Inputs/Power Failover. Size the energy budget against the reporting interval, not the peak — typical idle draw is 100mA@12VDC, so transmit frequency and session hold-time dominate. Fuse per the supply: 3 A for 9–24 VDC, 2.5 A for >24 VDC.

Conclusion: Design for the Line, Not the Point
A pipeline network is not judged by how well it performs on the day it is commissioned. It is judged in year five, when the line has been extended, the right-of-way has changed hands, the solar panel has been replaced twice and the question is whether anyone still knows what each of three hundred sites is doing and where it is.
Three things to settle before you specify connectivity for a pipeline:

—Draw the hazardous-area boundary first. Decide, with the operator’s safety authority, exactly where the classified zone begins. Everything outside that line is a standard industrial connectivity problem; everything inside it belongs to certified explosion-proof equipment, and no E-Lins router is offered for it. Getting this boundary on the drawing before you choose hardware prevents the one mistake on this list that is a safety issue rather than a cost issue.
—Separate what is tied to ground from what is tied to the line. The pump station and the terminal are built once. The valve stations, CP rectifiers and metering skids are built to be extended, re-powered and re-found — and they should be specified, named by chainage and provisioned as relocatable infrastructure, not as installations.
—Treat the alarm path, the power budget and the enclosure as design decisions, not accessories. An SMS alarm that leaves the site when the data tunnel is down, a power design sized against the reporting interval, and the correct ingress rating for the actual location are what keep a pipeline network honest. The router makes them possible; it does not make them for you.

Building Pipeline Connectivity Outside the Hazardous Area?

Tell E-Lins your site types, the jobs each site has to do, your power sources and your exposure conditions. We’ll confirm the serial and digital I/O configuration, the GNSS option, the PoE direction, the temperature and ingress rating, and the right platform — H685, H700, H750, H900/H900f, H820QO, M300 or M400 — for the network you actually operate. For hazardous areas, we will say plainly that the equipment is not ours to supply.

Leave a Reply

Your email address will not be published. Required fields are marked *

Contact Us

Have a question or need assistance? Fill out the form below, and we’ll get back to you as soon as possible.